Menu

CRESTRON CP2E MANUAL PDF

0 Comments

CP2E – read user manual online or download in PDF format. Pages in total: from the Crestron website (). 2. CP2E only. 2- Series Engine. At the heart of the CP2 & CP2E is the powerful bit Freescale. Crestron CP2E Pdf User Manuals. View online or download Crestron CP2E Operation Manual.

Author: Faegal Shakalkis
Country: Madagascar
Language: English (Spanish)
Genre: Video
Published (Last): 5 January 2018
Pages: 213
PDF File Size: 3.92 Mb
ePub File Size: 19.17 Mb
ISBN: 630-9-92864-768-2
Downloads: 94601
Price: Free* [*Free Regsitration Required]
Uploader: Gokora

Crestron recommends that you use the latest software to take advantage of the most recently released features. Pressing it alone while creatron system is running restarts the program.

Crestron electronic CP2E User Manual

Page 2 This document was prepared and written by the Technical Documentation department at: The foregoing remedy shall be your exclusive remedy for any claim or loss arising from the Software. To prevent bodily injury when mounting or servicing this unit in a rack, take special precautions to ensure that the system remains stable. Securing a tie wrap around the bussing strip is a useful way to provide strain relief for the wires connected to the terminal block. Don’t have an account?

Loosen the terminal block screws and insert the first leg of the bussing strip into the first common position of the terminal block. This Agreement may only be modified by a writing signed by an authorized officer of Crestron. IR output up to 1.

The only tool required is a 2 Phillips screwdriver. This device complies with part 15 of the FCC rules. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. If Cresnet HP is used for the same run, its length could extend to feet. Either cresrron, modify, or delete entries in the IP table. To print the manual completely, please, download it. Verify that serial cable is wired correctly for RS, or If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to manaul the interference by one or more of the following measures: The Cresnet Poll Accelerator effectively increases the network speed, fan-out and device addresses by a factor of 8 for each Poll Accelerator added to the system.

  ENDOSAFE PTS PDF

Crestron electronic CP2E User Manual – Page 1 of 40 |

Page of 28 Go. Verify that proper IR or serial port is defined. Consideration must be given if installed in a closed or multi-unit rack assembly since the operating ambient temperature of the rack environment may be greater than the room ambient temperature. Updates may be licensed to You by Crestron with additional or different terms.

CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures.

Please use the Crestron Power Calculator to help calculate how much power is needed for the system http: Confirm properly defined signal definition in the program. If power is supplied through Cresnet cabling, ensure the cable is securely plugged into the NET connector. Under normal conditions, it will last for approximately 10 years. All Crestron certified Cresnet wiring must consist of two twisted pairs.

Dispose of used batteries according to the manufacturer’s instructions. If this software requires payment for a license, you may make one backup copy of the Software, provided Your backup copy is not installed or used on any CPU. Therefore, you must treat the Software like any other copyrighted material, subject to the provisions of this Agreement.

Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. Future Updates For assistance in your local time zone, refer to the Crestron website http: Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

This Agreement may only be modified by a writing signed by an authorized officer of Crestron. If Cresnet units are to be daisychained on the run, the Cresnet power usage of each network unit to be daisychained must be added together to determine the Cresnet power usage of the entire chain. Return And Warranty Policies Purchasers should inquire of the manusl regarding the nature and extent of the dealer’s warranty, if any.

  CALDO BRILA PDF

For assistance in your local time zone, refer to the Crestron website http: Purchasers should inquire of the dealer regarding the nature and extent of the dealer’s warranty, if any. Ethernet CP2E only Crestron pioneered the IP-based control system to harness the vast possibilities of Ethernet and the Internet for remote control, monitoring, programming and diagnostics. The pinout of each 9-pin port is non-standard; it contains RS pins in addition cp2f RS Illuminates when a message is detected.

Programming Software SystemBuilder from the Crestron website and examine the extensive help file.

Crestron CP2E Manuals

In no event shall CRESTRON be liable for incidental or consequential damages of any kind property or economic damages inclusive arising from the sale or use of this equipment. Device is not receiving sufficient power. Position a rack ear so that its mounting holes align with the holes vacated by the screws in step 1. This device complies with part 15 of the FCC rules. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return mnaual.

Control crrstron is not receiving power.

CRESTRON CP2 OPERATION MANUAL Pdf Download.

If further assistance is required, please contact a Crestron customer service representative. If power is supplied through an AC adapter, verify the DC output plug is properly attached to the control system and that the adapter is securely plugged into an outlet. For RS and —, pins 2, 3, 5, frestron and 8 are wired straight through.